Дослідження нового способу кування великих злитків на основі осадження заготовок з уступами

Authors

Keywords:

forging, upset, internal defects, ingot, ledges, defects welding, compressive strains.

Abstract

Markov O. E., Khvashchynskyi A. S., Musorin A. V., Lycenko A. A., Molodetskie V. V.  Study of new forging process of ingots based on deformation of workpieces with conical ledges

New process of workpieces upsetting with ledges has been developed and studied in the work. Workpiece's ratio length before deformation was H / D = 3.0. Strain and stress condition has been studied to find the sign and level of compress stresses in a forged piece. Moreover, the parameter of the stress state in the zone location of the cavities has been evaluated. The closing degree of axial cavities has been determined. This parameter has been found for different heights and diameters. It has been found that the workpiece upsetting with ledges leads to a uniform stress into the forged-piece body. During deformation on the perifical surface and in the central zone there is compress stress due to the formation forged-piece with the concave size. Moreover, there is a closing of the internal cavities and recess on the lateral surface. Effective geometrical parameters of the initial workpiece have been found. It has been established that a decrease in the diameter and an increase in the height of the ledges leads to a decrease in the convexity in the studied range of workpiece sizes. The convexity increases as the diameter of the ledges decreases. The “barrel” is leveled and during subsequent upsetting, the side surface of the workpiece takes on a shape close to cylindrical. The relative diameter and height of the protrusions should be d/D = 0.5…0.7 and h/D = 0.4…0.6, respectively, to close defects during upsetting. The effective degree of deformation is 50 %. Determined relations have been checked out by experimentally in the process of the ingot`s forging weight equal to 66.5ton. Obtained practical results confirms the FEM results. The results of the investigation have been introduction in the manufacturing. 

Author Biographies

Oleg Markov, Donbass State Engineering Academy (DSEA), Kramatorsk

Doctor of Technical Sciences, Full Professor, Head of Department

Anton Khvashchynskyi, Donbass State Engineering Academy (DSEA), Kramatorsk

Graduate student

Anton Musorin, Donbass State Engineering Academy (DSEA), Kramatorsk

Graduate student

Anton Lysenko, Donbass State Engineering Academy (DSEA), Kramatorsk

Graduate student

Vitalii Molodetskyi, Novokramatorsky Mashinostroitelniy Zavod (NKMZ), Kramatorsk

Head of Department

References

Wang J., Fu P., Liu H., Li D., Li Y. Shrinkage porosity criteria and optimized design of a 100-ton 30Cr2Ni4MoV forging ingot. Mater. Design. 2012. 35, pp. 446-456. http://dx.doi.org/10.1016/j.matdes.2011.09.056

Zhang X-X., Cui Z-S., Chen W., Li Y. A criterion for void closure in large ingots during hot forging. J Mater Process Tech. 2009. 209(4), pp. 1950-1959.. http://dx.doi.org/10.1016/j.jmatprotec.2008.04.051

Markov O.E., Perig A.V., Markova M.A., Zlygoriev V.N. Development of a new process for forging plates using intensive plastic deformation. International Journal of Advanced Manufacturing Technology. 2016. 83 (9-12), pp. 2159-2174. DOI: 10.1007/s00170-015-8217-5 http://doi.org/10.1007/s00170-015-8217-5

Chao Feng, Zhenshan Cui, Mingxiang Liu, Xiaoqing Shang, Dashan Sui, Juan Liu. Investigation on the void closure efficiency in cogging processes of the large ingot by using a 3-D void evolution model. Journal of Materials Processing Technology. 2016. 237 (2016), pp. 371–385. http://dx.doi.org/10.1016/j.jmatprotec.2016.06.030

Chao Feng, Zhenshan Cui, Mingxiang Liu, Xiaoqing Shang, Dashan Sui, Juan Liu. Investigation on the void closure efficiency in cogging processes of the large ingot by using a 3-D void evolution model. Journal of Materials Processing Technology. 2016. 237, pp. 371–385. http://dx.doi.org/10.1016/j.jmatprotec.2016.06.030

Markov O. E., Gerasimenko O. V., Kukhar V. V., Abdulov O. R., Ragulina N. V. Computational and experimental modeling of new forging ingots with a directional solidification. Journal of the Brazilian Society of Mechanical Sciences and Engineering. 2019. 41(8). doi: http://doi.org/10.1007/s40430-019-1810-z

Markov O.E. Forging of large pieces by tapered faces. Steel in Translation. 2012. 42(12), pp. 808-810. doi: http://dx.doi.org/10.3103/S0967091212120054

Markov O., Zlygoriev V., Gerasimenko O., Hrudkina N., Shevtsov S. Improving the quality of forgings based on upsetting the workpieces with concave facet. Eastern-European Journal of Enterprise Technologies. 2018. 5 (1-95), pp. 16-24. DOI: http://doi.org/10.15587/1729-4061.2018.142674

Lee Y.S., Lee S.U., Van Tyne C.J., Joo B.D., Moon Y.H. Internal void closure during the forging of large cast ingots using a simulation approach. J Mater Process Tech. 2011. 211(6), pp. 1136-1145. http://dx.doi.org/10.1016/j.jmatprotec.2011.01.017.

Published

2022-12-21

How to Cite

Markov, O., Khvashchynskyi, A., Musorin, A., Lysenko, A., & Molodetskyi, V. (2022). Дослідження нового способу кування великих злитків на основі осадження заготовок з уступами. Materials Working by Pressure, (1(51), 61–70. Retrieved from http://omd.dgma.donetsk.ua/index.php/main/article/view/190

Issue

Section

SECTION II PRESSURE TREATMENT PROCESSES IN MECHANICAL ENGINEERING

Most read articles by the same author(s)