Assessment of the elongation of the ductility life of a structural aluminum alloy of the Al-Mg-Sc system using thermomechanical processing methods

Authors

  • Andrii Titov National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" (NTUU "Igor Sikorsky KPI"), Kyiv https://orcid.org/0000-0002-2245-5650
  • Vitalii Koreva National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" (NTUU "Igor Sikorsky KPI"), Kyiv https://orcid.org/0009-0005-2069-1026
  • Oleksandr Tymoshenko National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" (NTUU "Igor Sikorsky KPI"), Kyiv https://orcid.org/0000-0003-0226-3755

DOI:

https://doi.org/10.37142/2076-2151/2023-1(52)64

Keywords:

plasticity resource, structural materials, thermomechanical processing, aluminum alloy, tensile strength.

Abstract

Titov A., Koreva V., Tymoshenko O. Assessment of the elongation of the ductility life of a structural aluminum alloy of the Al-Mg-Sc system using thermomechanical processing methods.

A method has been developed and research has been carried out on extending the ductility life of a structural aluminum alloy of the Al-Mg-Sc system by thermomechanical processing using intermediate annealing during deformation processes. Tests were carried out on samples using a tensile scheme. To conduct an experimental study to determine the elongation of plasticity life by thermomechanical treatment, samples from a 2 mm thick sheet of aluminum alloy of the Al-Mg-Sc system were used. The research results are presented for various coefficients of plasticity resource utilization at the i-th transition. The value of the total realized plasticity has been established, reflecting the influence of intermediate heat treatment operations on the plasticity of the alloy after mechanical treatment by deformation. As a result, it was established that the drop in the efficiency of intermediate annealing is explained by the accumulation of metal damage during preliminary deformation. It has been established that intermediate annealing ensures an increase in the plasticity life of the material by 1.5...1.6 times. The dependence of the total realized plastic deformation on the number of “D+HT” cycles, the dependence of the residual plasticity life on the i-th cycle on the number of cycles, and the dependence of the plasticity resource recovery coefficient on the number of “D+HT” cycles are presented. The limiting surface of the dependence of the plasticity of the material on thermomechanical processing and the number of transitions based on the results of a complete study has also been constructed, which determines the plasticity of the material depending on the number of processing cycles “deformation + heat treatment” and allows you to select the parameters of the workpieces at the design stage of the technological process. 

Author Biographies

Andrii Titov, National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" (NTUU "Igor Sikorsky KPI"), Kyiv

Candidate of Technical Sciences, Associate Professor, NTUU "Igor Sikorsky KPI"

Vitalii Koreva, National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" (NTUU "Igor Sikorsky KPI"), Kyiv

Graduate student, NTUU "Igor Sikorsky KPI"

Oleksandr Tymoshenko, National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" (NTUU "Igor Sikorsky KPI"), Kyiv

Candidate of Technical Sciences, Associate Professor, NTUU "Igor Sikorsky KPI"

References

Bogatov A. A. Mechanical properties and models of destruction of metals: textbook for universities. Ekaterinburg: State Educational Institution of Higher Professional Education USTU-UPI. 2002. 329 p. (in Russian).

Kolmogorov V.L. Mechanics of metal forming: a textbook for high schools. Moscow: Metallurgy. 1986. 688 p. (in Russian).

Shpagin A.S., Kucheryaev V.V., Bubnov M.V. Computer modeling of thermomechanical processing of heat-resistant nickel alloys VZh175 and EP742. Proceedings of VIAM. 2019. No. 8 (80). pp. 27–35. (in Russian).

Smirnov S.V., Bogatov A.A., Kolmogorov V.L. Study of plastic loosening of metal and healing of deformation defects during annealing. Physics of metals and metallurgy. 1980. T. 49, issue. 2. pp. 389–393. (in Russian).

Matsevity V.M., Vakulenko K.V., Cossack I.B. On the healing of defects in metals during plastic deformation (analytical review). Problems of mechanical engineering. 2012. T. 15, No. 1. pp. 66–76. (in Russian).

Smirnov S.V., Nesterenko A.V., Shveikin V.P. Determining relations of damage mechanics for molybdenum under warm deformation. Fundamental research. 2012. No. 11-3. pp. 660–664. (in Russian).

Zhbanov Ya.G., Alieva L.I., Mikhalevich V.M. Restoration of plasticity during isothermal hot fractional deformation. Forging and Stamping Production. Material Working by Pressure. 2013. No. 7. pp. 12–17. (in Russian).

Matviychuk V.A., Aliev I.S. Improving the processes of local rotational pressure treatment based on the analysis of metal deformability: monograph. Kramatorsk: DSMA, 2009. 268 p. (in Russian).

DSTU ISO 6892-1:2019. Metal materials. Tensile test. Part 1. Test method at room temperature. Kyiv. 2020. 70 p. (in Ukrainian).

Published

2023-11-04

How to Cite

Titov, A., Koreva, V., & Tymoshenko, O. (2023). Assessment of the elongation of the ductility life of a structural aluminum alloy of the Al-Mg-Sc system using thermomechanical processing methods. Materials Working by Pressure, (1(52), 64–70. https://doi.org/10.37142/2076-2151/2023-1(52)64

Issue

Section

SECTION II PRESSURE TREATMENT PROCESSES IN MECHANICAL ENGINEERING